Please enable Javascript to continue to Phidgets.com
The core of our product line, the USB VINT Hub has 6 VINT ports allowing for endless possibilities for USB sensing and control.
Use Phidgets in your local network with this 6 port Wireless VINT Hub. Works with ethernet or a WiFi network.
Single Board Computer running Debian with 3 high-speed USB ports and 6 VINT ports. 512 MiB SDRAM and 8 GB SD Card.
Connect a pH probe or any voltage-based probe that uses a BNC connector to your VINT port with this isolated adapter.
With eight analog ports, you can connect a bunch of 5V sensors or measure small voltage signals.
Add 4 digital inputs to your VINT Hub. These inputs have a shorter trigger time than a VINT port in Digital Input mode.
Add 4 isolated active-high digital inputs to your hub at the cost of only one VINT port.
Add 16 isolated active-high digital inputs to your hub at the cost of only one VINT port.
Reads one 4-20mA, frequency output, PNP/NPN or 5V sensor, and provides 12 or 24V without an external supply.
Measure up to 2 load cells or Wheatstone Bridge-based sensors with this input module. Connects to a VINT port.
Control one high-current brushed DC motor with this powerful Phidget. The encoder input and analog input can enable precise control motor velocity and position.
Control a single DC motor up to 4A with this compact and affordable Phidget. Connects to a VINT port.
Control two DC motors from one VINT port with this compact motor controller.
Control a brushless DC motor from your VINT Hub. The hall effect input enables easy position and velocity control.
Measure distances up to 170mm with this infrared time-of-flight sensor. Connects to a VINT port.
Measure distances up to 650mm with this infrared time-of-flight sensor. Connects to a VINT port.
Measure distances up to 1300mm with this infrared time-of-flight sensor. Connects to a VINT port.
Detect several solid objects up to 10m away in a wide sensing range, or use this Phidget as an ultrasonic range finder.
Interface a quadrature encoder at speeds of up to 100,000 quadrature cycles per second to a port on your VINT Hub.
Use this array of capactive touch buttons as a unique way to control your Phidgets.
Use this capacitive touch wheel and buttons as an intuitive user interface to your Phidgets system.
Make a custom controller for your project with this thumbstick. Two-axis with a center pushbutton, it plugs into a VINT port.
This dial has a fully continuous range of motion and a center pushbutton. Connects to a VINT port.
Measure relative humidity from 0 to 100% and temperature from -40°C to +85°C.
Write text and draw pictures to this 128x64px graphic LCD display that connects to a VINT port.
Control the current, voltage and brightness of 32 LEDs from a VINT port with this externally powered module.
This light sensor measures from 188 μlux to 220 klux and connects to any VINT port.
Measure acceleration up to ±8g in each axis with the 3-Axis Accelerometer Phidget. Connects to a VINT port.
An accelerometer, gyroscope, and magnetometer all in one board. Measuring in 3 axes, it plugs right into your VINT hub.
Produce a voltage from 0 to 4.2 volts with this simple voltage output module.
Produce a voltage from -10 to +10 volts with this isolated voltage output module.
Produce a voltage from -10 to +10 volts with this 16-bit isolated voltage output module.
Add four 5V PWM-enabled digital outputs to your hub with this simple and affordable module.
Precisely measure the absolute air pressures between 50 and 110 kPa with this barometer that connects to any VINT port.
This wall socket makes it easy for your VINT Hub to switch power to a device or appliance.
Control position, velocity, and acceleration of 16 RC servos with just one VINT port.
Switch the power of up to four circuits at 210W of DC power or 1750 VA of AC power with this mechanical relay module.
Add four PWM-enabled solid state relay outputs to your hub with this module. This board is isolated to prevent ground loops.
Add 16 PWM-enabled solid state relay outputs to your hub. This module is isolated from input to output.
Protect your circuit and power supply by detecting and preventing overvoltage and overtemperature situations.
Measure sound from 34 to 102 dB (SPL). Supports A and C weightings, and can split data into distinct frequency bands.
Control the position, velocity, and acceleration of one high-power stepper motor with this Phidget.
This compact Stepper Phidget gives you control of one bipolar stepper motor from a port on your VINT hub.
This Phidget connects to a VINT port and measures ambient temperature from -40°C to 85°C quickly and easily.
Connect one K, J, E or T type thermocouple to this Phidget to measure the temperature of the air, an object, or a liquid.
Connect up to four K, J, E or T type thermocouples to this Phidget to measure the temperature of the air or an object.
Measure RTDs, thermistors, and other resistance-based sensors with this VINT port adapter.
Measure up to ±40V with this high precision isolated voltage input Phidget. Connects to a VINT port.
This Phidget measures voltage potentials of up to ±40V. It connects to a VINT port and is isolated for increased reliability.
Measure tiny voltage differences of up to ±1V with precision. This Phidget is isolated and plugs into a VINT port.
Measure in-line DC current flow of up to 30A with this Phidget that connects to a VINT port.
This powered 7-port USB 2.0 hub is ideal for projects that use multiple USB Phidgets.
Measure acceleration up to ±8g in each axis with the PhidgetAccelerometer. Connects via USB or VINT.
This spatial board has a 3-axis accelerometer, gyroscope and compass with high resolution readings at low magnitudes.
This board has 4 SPDT mechanical relays rated at 210W for DC or 1750VA for AC.
Control 8 DPDT mechanical relays, switching up to 250VAC/2amp or 200VDC/2amp.
A 1018 with an on-board powered 6-port full-speed (12Mbit/s) USB hub.
A Phidget InterfaceKit with a 2-line by 20-character White Backlit LCD Display.
This convenient adapter makes your hub's 5V USB voltage accessible on a terminal block and can be switched using a Digital Output.
This adapter provides an adjustable 1.5 to 5V from your hub's USB voltage, and can be turned on and off as a Digital Output.
This adapter provides an adjustable 6 to 24V from your hub's USB voltage, and can be turned on and off as a Digital Output.
Use a VINT port with this relay to switch power to a circuit running at up to 210 watts DC or 1750 volt-amperes AC.
Switch a small digital signal with this DPDT mechanical relay Phidget. Switch up to 60W of DC power or 125 VA of AC power.
This solid state relay module can switch up to 30V and 10A AC or DC using a port on your VINT Hub.
Protect your power supply from surges caused by sudden braking on a motor controller with this tiny Phidget.
A USB isolator to shield your computer from USB devices. Also useful in eliminating ground loops in complex systems.
A credit card sized EM4102 RFID tag. Fits in standard wallets.
For use with the E4P encoders on the back of some of our DC motors.
For use with the HKT22 encoder.
This adapter cable will allow you to connect serial devices to the SBC's USB port.
This magnetic switch can detect magnets within 12mm and connects to a digital input. Magnet included.
A pushbutton switch with a roller-ball form factor. Perfect for door jambs or other locations where movement is expected.
A simple micro switch. Excellent for implementing custom limit switches and more.
Micro switch with a roller on the lever. Good for limit switches and more.
These are extra bright for applications where light matters.
These LEDs have a soft glow, making them great for indicators.
A 10W LED flood light, great for exterior lighting.
A 2 line by 20 character backlit LCD display. Each character is 3.2x5.55mm.
A 2 line by 20 character backlit LCD display. Each character is 5.9x12.7mm.
A 2 line by 40 character backlit LCD display. Each character is 3.2x5.55mm.
A 4 line by 20 character backlit LCD display. Each character is 2.95x4.75mm.
A 4 line by 40 character backlit LCD display. Each character is 2.78x4.89mm.
Fast acting automotive fuses. Assorted amperages.
This fuse socket provides a quick and easy way to add an automotive fuse to your system.
This tiny wireless adapter will enable your SBC4 to connect to your home wi-fi network.
This clear acrylic enclosure protects your Phidget and is assembled with a Phillips screwdriver.
A blue ABS key fob RFID tag. Uses EM4102 protocol.
An RFID tag embedded in a button ideal for tracking clothing inventory. Uses EM4102 protocol.
An RFID tag on an adjustable wristband. For when you need to keep track of lots of people. Uses EM4102 protocol.
An RFID tag on an elastic wristband. For when you need to keep track of lots of people. Uses EM4102 protocol.
A small PVC disc with an RFID tag embedded in it. Uses EM4102 protocol.
A PVC disc with an RFID tag embedded in it. Uses EM4102 protocol.
A plastic disc with an EM4012 tag embedded in it. A nail or screw through the hole in the center makes for easy mounting.
Designed to fit into a hole found on common waste bins but can be used with any matching threads. Uses EM4102 protocol.
Ever heard of animal tagging? Here's how they do it. Designed for mid-sized birds like a chicken. Uses EM4102 protocol.
A credit card sized RFID tag. Fits in standard wallets. Needs to be written to before use.
A writable, grey ABS key fob RFID tag. Needs to be written to before use.
A writable RFID tag on an adjustable wristband. Ideal for keeping track of people. Must be written to before use.
A plastic disc with a writable RFID tag in it. The hole makes for easy mounting. Must be written to before use.
A small PVC disc with an RFID tag embedded in it. Must be written to before use.
A PVC disc with an RFID tag embedded in it. Must be written to before use.
An EM4012 RFID tag that can even be read when it is in close proximity to metal. If you want to use a tag on metal this is it.
This small project box keeps your Phidgets safe from pokes, prods, and foreign debris.
This mid-size project box keeps your Phidgets safe from pokes, prods, and foreign debris.
This mid-sized project box keeps your Phidgets safe from pokes, prods, and foreign debris.
This large project box keeps your Phidgets safe from pokes, prods, and foreign debris.
A convenient way to plug your power supply into any circuit. 5.5x2.1mm female connector.
Two meter CAT5E cable for use with Phidget SBCs.
2 Conductors, 16AWG each. Cut to length (in m).
4 Conductors Shielded cable, 16AWG each. Cut to length (in m).
4 Conductors, 16AWG each. Cut to length (in m).
8 Conductors Shielded cable, 20AWG each. Cut to length (in m).
8 Conductors, 20AWG each. Cut to length (in m).
12 Conductors Shielded cable, 22AWG each. Cut to length (in m).
12 Conductors, 22AWG each. Cut to length (in m).
Wire for hooking up devices to terminal blocks or breadboards. Cut to length (in meters).
Extension wire to match our 3-wire Phidget Cables.
These waterproof cable glands allow you to pass cables into your waterproof enclosure without letting water in.
These waterproof connectors allow you to attach 2 cables together while protecting the connection from the elements.
Waterproof limit switch with a roller head.
Waterproof limit switch with an adjustable (50mm) roller head.
Waterproof limit switch with an adjustable (96mm) rod head.
Waterproof limit switch with a button head.
Waterproof limit switch with a flex head.
A modular, stackable aluminium plate with mounting holes to match most Phidgets.
100 meters of hook-up wire, of various colours and gauges.
This 24V power supply clips on to 35x7,5mm DIN rail.
Adjusts between 22 and 28V and provides 14.6A of current. Compatible with either 120V or 240V input.
Adjusts between 22 and 26V and provides 25A with current limiting if your system tries to draw more current.
Provides a US wall plug for brick-style power supplies.
Provides a UK wall plug for brick-style power supplies.
Provides an EU wall plug for brick-style power supplies.
Provides an AU wall plug for brick-style power supplies.
A PVC disc with a writable RFID tag embedded in it. Must be written to before use.
This wireless adapter will enable your SBC4 to connect to your home wi-fi network.
This 720p USB webcam is ideal for use with your Phidget SBC.
An adapter dongle for the SBC that enables audio input and output.
