Phidgets

Outputs a voltage from -10V to +10V.

The ideal product for OEMs and Systems Integrators. The small DIP-36 package will plug right into your own designed board.

Small Dongle with 2 Analog Inputs, 2 Digital Inputs and 2 Digital Outputs. Use it when space is critical.

Use it to check the state of switches and push buttons, and/or to switch relays, solenoids, and LEDs.

This board has 4 SPDT mechanical relays rated at 210W for DC or 1750VA for AC.

Control 8 DPDT mechanical relays, switching up to 250VAC/2amp or 200VDC/2amp.

The Phidgets workhorse. Connect sensors, control outputs, and read in digital inputs.

A 1018 with an on-board powered 6-port full-speed (12Mbit/s) USB hub.

Read and write to RFID tags up to 6cm away. Supports EM4100 series, ISO11785 FDX-B and our own PhidgetTag protocols.

This Phidget uses current control to adjust the brightness of up to 64 LEDs.

This board is needed to measure the output from a load cell. You can connect up to four load cells or strain gauges.

Measures the frequency of a signal and powers small devices like Hall Effect sensors, flow rate sensors, and tachometers.

Send and receive IR data with this Phidget. It can learn and reproduce signals from common devices like your TV remote.

Control up to 8 RC servo motors or actuators with this controller board. Connects to your computer via USB.

Accurately control up to 4 unipolar stepper motors with this controller. Connects to a USB port.

Control up to two DC motors with this controller. Monitors surges and overheating in the API and connects to a USB port.

Control one motor as well as an encoder and up to 2 analog and 2 digital sensors. Connects to a USB port.

Control one RC servo motor or actuator with this controller board. Powered solely by your computer via USB.

Accurately control one bipolar stepper motor with this controller. This board comes with a number of safety features.

Single board computer running Debian 7.0 with 128 MiB SDRAM, 1 GiB Flash, integrated 1018 and 6 USB 2.0 ports.

This adapter lets you read Sharp distance sensors with a Phidgets Analog Input or VINT Hub port.

The FlexiForce adapter allows you to connect one FlexiForce FSR to a an Analog Input or VINT Hub port.

This adapter lets you interface with all sorts of non-Phidgets resistance sensors, just dial in the resistance you want.

The pH/ORP Adapter connects any of our pH or ORP probes to an Analog Input or VINT Hub port.

A common output mode for industrial sensors is 4-20mA. This adapter lets you use 4-20mA sensors with an Analog Input or VINT Hub port.

This adapter lets you interface with all sorts of non-Phidgets resistance sensors, just select the resistance you want.

Phidgets mostly run on 5V, but if you need 12V to power up your sensor you can use this adapter.

Phidgets mostly run on 5v, but if you have a ±12V sensor you can use this adapter.

A Phidget InterfaceKit with a 2-line by 20-character White Backlit LCD Display.

A dual channel LCD controller that is compatible with HD44780 LCD modules.

This board has 2 SPDT mechanical relays rated at 210W for DC or 1750VA for AC.

Rated for 28VAC/2.5amp or 40VDC/2.5amp switching, this SSR is controlled by a digital output.

Switch 2 SSRs rated for 28VAC/9amp or 40VDC/9amp using digital outputs.

Rated for 28VAC/0.5amp or 40VDC/0.5amp switching, this SSR is controlled by a digital output.

This adapter cable will allow you to connect serial devices to the SBC's USB port.

24-bit color and a built in mic. Compatible with 1072 - SBC2 Not compatible with the 1073 - PhidgetSBC3.

This wireless adapter will allow your SBC to connect to a wireless network. Recommended for the PhidgetSBC2.

This wireless adapter will allow your SBC to connect to a wireless network. Recommended for the PhidgetSBC3.

This SSR switches up to 30VDC/50amp and connects to a PhidgetInterfaceKit 0/16/16.

This SSR switches up to 50VDC/80amp and connects to a PhidgetInterfaceKit 0/16/16.

This SSR switches up to 30VDC/100amp and connects to a PhidgetInterfaceKit 0/16/16.

Use this heatsink to run one SSR at full current switching capacity without overheating.

This SSR switches up to 120VDC / 25A and connects to any device with a digital output.

This SSR switches up to 120VDC / 75A and connects to any device with a digital output.

This SSR switches up to 280VAC / 25A and connects to any device with a digital output.

Use this heatsink to run one high current SSR without overheating.

Connect a pH probe or any voltage-based probe that uses a BNC connector to your VINT port with this isolated adapter.

Two meter CAT5E cable for use with Phidget SBCs.

With eight analog ports, you can connect a bunch of 5V sensors or measure small voltage signals.

Add 4 digital inputs to your VINT Hub. These inputs have a shorter trigger time than a VINT port in Digital Input mode.

Add 4 isolated active-high digital inputs to your hub at the cost of only one VINT port.

Add 16 isolated active-high digital inputs to your hub at the cost of only one VINT port.

Reads one 4-20mA, frequency output, PNP/NPN or 5V sensor, and provides 12 or 24V without an external supply.

Measure up to 2 load cells or Wheatstone Bridge-based sensors with this input module. Connects to a VINT port.

Control one high-current brushed DC motor with this powerful Phidget. The encoder input and analog input can enable precise control motor velocity and position.

Interface a quadrature encoder at speeds of up to 100,000 quadrature cycles per second to a port on your VINT Hub.

The core of our product line, the USB VINT Hub has 6 VINT ports allowing for endless possibilities for USB sensing and control.

Control the current, voltage and brightness of 32 LEDs from a VINT port with this externally powered module.

Produce a voltage from 0 to 4.2 volts with this simple voltage output module.

Produce a voltage from -10 to +10 volts with this isolated voltage output module.

Produce a voltage from -10 to +10 volts with this 16-bit isolated voltage output module.

Add four 5V PWM-enabled digital outputs to your hub with this simple and affordable module.

Switch the power of up to four circuits at 210W of DC power or 1750 VA of AC power with this mechanical relay module.

Add four PWM-enabled solid state relay outputs to your hub with this module. This board is isolated to prevent ground loops.

Add 16 PWM-enabled solid state relay outputs to your hub. This module is isolated from input to output.

Use a VINT port with this relay to switch power to a circuit running at up to 210 watts DC or 1750 volt-amperes AC.

Switch a small digital signal with this DPDT mechanical relay Phidget. Switch up to 60W of DC power or 125 VA of AC power.

Single Board Computer running Debian with 3 full-speed USB ports and 6 VINT ports. 512 MiB SDRAM and 16 GB SD Card.

Control the position, velocity, and acceleration of a stepper motor from your VINT port with this powerful controller.