Products for USB Sensing and Control Canada flag
Products for USB Sensing and Control

sales inquiries

quotes, distributor information, purchase orders

technical inquiries

support, advice, warranty, returns, misshipment

website inquiries

corrections or suggestions


Unit 1 - 6115 4 St SE
Calgary AB  T2H 2H9


Unit 1 - 6115 4 St SE
Calgary AB  T2H 2H9
+1 403 282-7335

USB to Serial Converter

ID: 3400_1

This adapter cable will allow you to connect serial devices to the SBC's USB port.


Quantity Available: 281

Qty Price
5 $3.80
10 $3.60
25 $3.20
50 $2.80
100 $2.60

The USB to Serial Converter Cable is ideal for connecting RS232 devices to any of the PhidgetSBC's USB ports.

The SBC will automatically recognize the Converter when it is plugged in and will create a serial port for it.

Be aware that the 3400 and any serial devices connected to it are not "Phidgets devices" and therefore cannot be accessed or controlled by the Phidgets' APIs. Using this product requires a working knowledge of Linux.

Note: This device is not compatible with Windows 8 or newer.


  • Connect RS232 devices to your PhidgetSBC
  • No cable driver installation required on PhidgetSBC

Single-Board Computer

This serial adapter is recommended for use with the following Phidget SBCs:

Product SBC
Part Number Price CPU CPU Speed NAND Memory Size SDRAM Size Operating System
$120.00 Allwinner A20 **Up to 960 MHz 512 MiB

Go to this device's product page

Getting Started

The 3400 USB to Serial Converter allows you to connect Serial Devices to the PhidgetSBC using one of its USB connectors.

The USB to Serial Converter is not a Phidget device and therefore, the Converter or any devices connected to it cannot be controlled using Phidgets APIs. Using this product requires a working knowledge of Linux.

Here is a short manual showing you how to use the Converter on a PhidgetSBC.

Connect the Converter to the PhidgetSBC

1. Log onto the SBC via SSH. Your SBC may be running an older version of firmware that does not support the USB to Serial Converter, requiring you to update your SBC firmware to the latest version.

3400 0 Connecting The Hardware.jpg

2. Plug the USB to Serial converter into an available USB port on the Phidget SBC. The SBC should automatically recognize the converter.

3. Type dmesg | tail –n 5 on the SBC to view the last 5 lines of the kernel’s message buffer. You should see something similar to the lines below:

usb 1-1.1: new full speed USB device using s3c2410-ohci and address 8
usb 1-1.1: configuration #1 chosen from 1 choice
pl2303 1-1.1:1.0: pl2303 converter detected
usb 1-1.1: pl2303 converter now attached to ttyUSB0

The SBC has recognized the Prolific PL2303 USB to serial converter, and has created a new serial port for it, which can be accessed at /dev/ttyUSB0

Test the Converter using your PC serial port

One way of testing the USB to Serial Converter is by connecting the SBC to a serial port on your PC using a Null modem cable. If your computer does not have a serial port, you can still perform the test by using a second USB to Serial Converter to connect the Null modem cable to a USB port on your PC.

Log in via the Serial Converter

Remount the root filesystem on the SBC as read/write so that we can make changes to it. Type the following command:

mount –o remount rw /

4. Make a backup copy of our inittab file. We will be changing this file, so it’s a good idea to have a backup to revert to, should anything go wrong. Type the following:

cp /etc/inittab /etc/inittab.backup

5. Use the vi editor on the SBC to edit /etc/inittab and add the following line to the file; this command tells the SBC to start a terminal on ttyUSB0 using 115200 baud bitrate, and vt100 emulation. Type the following:

ttyUSB0:23:respawn:/sbin/getty -L ttyUSB0 115200 vt100

6. Edit /etc/securetty, and add ttyUSB0 to the end of the file. This is the list of devices that root is allowed to log on from.

7. Reboot the SBC using the reboot command

Make sure everything works

1. Connect the serial converter to your PC’s serial port using a null modem cable.

3400 0 PuTTY Screen.jpg

2. Open up the com port (eg: COM1) on your PC using a terminal program like hyperterminal, or PuTTY, using 115200 as the baud rate.

3400 0 PuTTY Connected.jpg

3. When connected, you will see a login prompt similar to the one below. You can now log in to your SBC via the serial port just like you would from an SSH connection.

3400 0 Serial Adapter To Computer.jpg

4. Be sure to undo the changes you have made in the /etc directory.

Communication from a C program

You should already have your USB to Serial adapter plugged in, and it should already be attached as /dev/ttyUSB0. Included on the USB to Serial Converter product page is an example c program that you can use to echo text sent from a host computer back to it.

This program is configured to run at 38400 baud. Compile and execute it on the SBC. Plug your Null Modem cable into the PC and set up a connection to run at 38400 baud. When you type a string on the PC, followed by Enter, the SBC will add ‘1’ to each character and echo it back to you.

"I accidentally connected the device before installing the drivers and now it won't work, what should I do?"

The newer drivers from Prolific do not work for the chipset in this device. If you connect the device to your computer before installing the correct drivers Windows will look for the latest drivers available from the device manufacturer. It will find drivers which are not compatible and the device will appear to not work. To fix this problem follow these steps:

  • Open the device in the Windows Device Manager.
  • Go to the Driver tab.
  • Uninstall the drivers, make sure to check the delete box to get rid of any local files that may be stored on your computer.
  • Plug the device in again and go back to the Device Manager.
  • Under the driver tab again choose Update Driver.
  • Choose "Browse my computer for a driver."
  • Choose "Let me pick from a list of device drivers on my computer."
  • Choose the older, 2008 version of the driver (assuming you have installed the drivers you downloaded from our website it should appear in the list).

The device should be functional now.

Product Specifications

Physical Properties
Connector A USB Type-A (Male)
Connector B RS-232 DB-9 (Male)
Cable Length 960 mm
I/O Communication Protocol USB 1.1 and USB CDC 1.1
Data Rate Max 1 Mbit/s
Buffer Size 96 B
Electrical Properties
Current Consumption Max 32 mA
Customs Information
Canadian HS Export Code 8473.30.00
American HTS Import Code 8473.30.51.00
Country of Origin TW (Taiwan)


NOTE: Please install these drivers before plugging the device into your computer. If it doesn't detect these drivers when plugged in, it will install incorrect ones. Click here to read how to fix the drivers if this happens.