Template:UgServo - Revision history

Lmpacent at 23:07, 14 June 2017

2017-06-14T23:07:12Z

← Older revision		Revision as of 23:07, 14 June 2017
Line 1:		Line 1:
	===RC Servo===		===RC Servo===
	Double-click on the RCServo object, labelled ''{{{2}}}'', in order to run the example:		Double-click on the RCServo object, labelled ''{{{2}}}'', in order to run the example:
	[[Image:{{{1}}}_Servo_Example.jpg\|~~right~~\|link=]]		[[Image:{{{1}}}_Servo_Example.jpg\|center\|link=]]

Lmpacent at 23:06, 14 June 2017

2017-06-14T23:06:57Z

← Older revision		Revision as of 23:06, 14 June 2017
Line 1:		Line 1:
	===RC Servo===		===RC Servo===
			Double-click on the RCServo object, labelled ''{{{2}}}'', in order to run the example:
	[[Image:{{{1}}}_Servo_Example.jpg\|right\|link=]]		[[Image:{{{1}}}_Servo_Example.jpg\|right\|link=]]

	~~When you double click on an RC Servo object, a window like the one pictured will open.~~

	* At the top of the window, information about your device and the properties of this particular channel will be listed.		{{UGExampleDescription}}
	* ~~Below that, motor~~ calibration options are provided. ~~Put~~ the minimum and maximum pulse widths for your servo in the appropriate boxes. You can also change which position these pulse widths map to.		*Motor calibration options are provided. You can change the minimum and maximum pulse widths for your RC servo motor in the appropriate boxes. You can also change which position these pulse widths map to.
	* In the ~~middle,~~ the ~~position, velocity,~~ and ~~stopped/started status of~~ the motor ~~(from the controller's point of view) is displayed in real time~~.		*The ''SpeedRampingState'' checkbox lets the {{{1}}} know whether or not to take the ''Acceleration'' and ''Velocity'' values into account when moving the RC servo motor.
	* At the ~~bottom, you can control~~ the position~~, acceleration,~~ and ~~speed of the motor. The enable/disable button toggles activation of~~ the motor ~~on this port~~.		*Use the ''Position'' slider to change the target position and move the RC servo motor.
	<br clear="all">		<br clear="all">

Jdecoux: /* RC Servo */

2017-06-12T21:32:23Z

RC Servo

← Older revision		Revision as of 21:32, 12 June 2017
Line 1:		Line 1:
	===RC Servo===		===RC Servo===

	[[Image:~~Servo_Example~~.jpg\|right\|link=]]		[[Image:{{{1}}}_Servo_Example.jpg\|right\|link=]]

	When you double click on an RC Servo object, a window like the one pictured will open.		When you double click on an RC Servo object, a window like the one pictured will open.

Mparadis: Created page with "===RC Servo=== link= When you double click on an RC Servo object, a window like the one pictured will open. * At the top of the window, i..."

2016-08-26T20:31:54Z

Created page with "===RC Servo=== right|link= When you double click on an RC Servo object, a window like the one pictured will open. * At the top of the window, i..."

New page

===RC Servo===

[[Image:Servo_Example.jpg|right|link=]]

When you double click on an RC Servo object, a window like the one pictured will open.

* At the top of the window, information about your device and the properties of this particular channel will be listed.
* Below that, motor calibration options are provided. Put the minimum and maximum pulse widths for your servo in the appropriate boxes. You can also change which position these pulse widths map to.
* In the middle, the position, velocity, and stopped/started status of the motor (from the controller's point of view) is displayed in real time.
* At the bottom, you can control the position, acceleration, and speed of the motor. The enable/disable button toggles activation of the motor on this port.
<br clear="all">