OUT1001 User Guide - Revision history

Mparadis: /* About */

2026-03-04T18:52:54Z

About

← Older revision		Revision as of 18:52, 4 March 2026
Line 13:		Line 13:
	[[Image:OUT1001_About.jpg\|link=\|center]]		[[Image:OUT1001_About.jpg\|link=\|center]]

	'''Note:''' The ~~10V terminal has~~ a ~~resolution~~ of 4.~~9 mV DC. The~~ 5V ~~terminal has a resolution of 1~~.~~2 mV DC~~.		'''Note:''' The two terminals cannot be controlled separately. You must select a single mode by setting the '''VoltageOutputRange''' in software, and only use the terminals for that mode. Because of this, the 5V terminal will produce 2.5V when the channel is not open. See advanced topics below for more information.

	===Explore Your Phidget Channels Using the Control Panel===		===Explore Your Phidget Channels Using the Control Panel===

Mparadis: /* Part 4: Advanced Topics and Troubleshooting */

2026-03-04T18:52:16Z

Part 4: Advanced Topics and Troubleshooting

@@ Line 60: / Line 60: @@
 For example, if the connected circuit is pulling 13mA of current, the OUT1001 will only be able to provide a maximum of 4V (in 0-5V mode), even if you try to set it to a higher value.}}
 {{UGC-Entry|I’m seeing strange readings when I start my program or when switching voltage range|
+|
 The OUT1001 may have an unpredictable output voltage for a very short time immediately after the device changes modes or is turned on. If this is a problem in your application, and you have no way to ignore it via software, we recommend using a [[Solid_State_Relay_Primer|solid-state relay]] to switch the output on once it has stabilized.}}
 {{UGC-End}}

Mparadis at 21:18, 17 January 2022

2022-01-17T21:18:24Z

← Older revision		Revision as of 21:18, 17 January 2022
Line 39:		Line 39:
	{{UGC-Start}}		{{UGC-Start}}
	{{UGC-Addressing}}		{{UGC-Addressing}}
			{{UGC-Firmware}}
	{{UGC-Entry\|Current Sourcing and Sinking\|		{{UGC-Entry\|Current Sourcing and Sinking\|
	\|		\|

Mparadis: /* Explore Your Phidget Channels Using the Control Panel */

2021-03-17T16:57:25Z

Explore Your Phidget Channels Using the Control Panel

← Older revision		Revision as of 16:57, 17 March 2021
Line 26:		Line 26:
	{{UGC-Start}}		{{UGC-Start}}

	{{UGC-Entry\|~~Voltage~~ Output: \|Produce a DC voltage for the connected circuit or device		{{UGC-Entry\|Isolated 12-bit Volage Output Phidget: \|Produce a DC voltage for the connected circuit or device
	\|		\|
	In your Control Panel, double click on "Isolated 12-bit Volage Output Phidget":		In your Control Panel, double click on "Isolated 12-bit Volage Output Phidget":
	[[Image:OUT1001-VoltageOutput.jpg\|center~~\|780px~~\|link=]]}}		[[Image:OUT1001-VoltageOutput.jpg\|center\|link=]]}}

	{{UGC-End}}		{{UGC-End}}

Mparadis at 20:32, 28 January 2021

2021-01-28T20:32:40Z

@@ Line 4: / Line 4: @@
 [[Category:UserGuide]]
 ==Part 1: Setup==
-{{UGIntro|OUT1001}}
+{{PT1 Deck Sequence}}
 == Part 2: Using Your Phidget ==

Mparadis at 21:26, 11 September 2020

2020-09-11T21:26:24Z

← Older revision		Revision as of 21:26, 11 September 2020
Line 26:		Line 26:
	===About===		===About===
	The OUT1001 can provide a DC voltage between -10V and +10V on the 10V terminal. The 5V terminal provides a voltage between 0V to 5V. This Phidget is ideal for analog voltage-controlled devices.		The OUT1001 can provide a DC voltage between -10V and +10V on the 10V terminal. The 5V terminal provides a voltage between 0V to 5V. This Phidget is ideal for analog voltage-controlled devices.

			[[Image:OUT1001_About.jpg\|link=\|center]]

	'''Note:''' The 10V terminal has a resolution of 4.9 mV DC. The 5V terminal has a resolution of 1.2 mV DC.		'''Note:''' The 10V terminal has a resolution of 4.9 mV DC. The 5V terminal has a resolution of 1.2 mV DC.

Mparadis at 18:46, 21 April 2020

2020-04-21T18:46:42Z

← Older revision		Revision as of 18:46, 21 April 2020
Line 1:		Line 1:
	__NOINDEX__		__NOINDEX__
			__NOTOC__
	<metadesc>Produce a voltage from -10 to +10 volts with the Isolated 12-Bit Voltage Output Phidget. Connects to a port on your VINT Hub.</metadesc>		<metadesc>Produce a voltage from -10 to +10 volts with the Isolated 12-Bit Voltage Output Phidget. Connects to a port on your VINT Hub.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==~~Getting Started~~==		==Part 1: Setup==
	{{UGIntro\|OUT1001}}		{{UGIntro\|OUT1001}}
	*[{{SERVER}}/products.php?product_id=OUT1001 OUT1001 - Isolated 12-bit Voltage Output Phidget]		*[{{SERVER}}/products.php?product_id=OUT1001 OUT1001 - Isolated 12-bit Voltage Output Phidget]
Line 19:		Line 20:
	{{UGIntroDone\|OUT1001}}		{{UGIntroDone\|OUT1001}}

	~~==Using the OUT1001==~~
	{{UGcontrolpanel\|OUT1001}}		{{UGcontrolpanel\|OUT1001}}

	~~{{ugVoltageOutput\|OUT1001\|, labelled ''Isolated 12-bit Voltage Output~~ Phidget~~'', }}~~		== Part 2: Using Your Phidget ==
	*Select the ''Voltage Output Range'' from the drop-down menu. You can choose between 0-5V output or ±10V output.

	~~{{ugAddressingInformation}}~~		===About===
			The OUT1001 can provide a DC voltage between -10V and +10V on the 10V terminal. The 5V terminal provides a voltage between 0V to 5V. This Phidget is ideal for analog voltage-controlled devices.

	~~{{ugUsingYourOwnProgram\|OUT1001}}~~		'''Note:''' The 10V terminal has a resolution of 4.9 mV DC. The 5V terminal has a resolution of 1.2 mV DC.

	~~==Technical Details==~~		===Explore Your Phidget Channels Using the Control Panel===
	===Control ~~Application=~~==
	~~[[Image:OUT1001_Control_Diagram.jpg\|link~~=~~\|350px\|right]]~~
	~~Some devices may require an analog voltage as a control input. The OUT1001 supplies a fixed voltage up to ±10V, which can be used to control such devices.~~

	~~In addition~~, ~~this device is isolated~~ and ~~can apply its~~ voltage ~~anywhere in an application~~ circuit, ~~independent of USB ground~~.		You can use your Control Panel to explore your Phidget's channels.
	~~<br clear~~=~~"all">~~
			'''1.''' Open your Control Panel, and you will find the '''Isolated 12-bit Volage Output Phidget''' channel:

			[[Image:OUT1001_Panel.jpg\|link=\|center]]

			'''2.''' Double click on the channel to open an example program. This channel belongs to the '''Voltage Output''' channel class:
			{{UGC-Start}}

			{{UGC-Entry\|Voltage Output: \|Produce a DC voltage for the connected circuit or device
			\|
			In your Control Panel, double click on "Isolated 12-bit Volage Output Phidget":
			[[Image:OUT1001-VoltageOutput.jpg\|center\|780px\|link=]]}}

			{{UGC-End}}

			{{UG-Part3}}

			== Part 4: Advanced Topics and Troubleshooting ==

			{{UGC-Start}}
			{{UGC-Addressing}}
			{{UGC-Entry\|Current Sourcing and Sinking\|
			\|
			The OUT1001 should be subjected to a minimal current draw to ensure maximum voltage precision across the device's full range (less than 5mA in ±10V mode). 5V mode should only be used to set a voltage in high-impedance applications.

	~~===Transient Voltages===~~		However, in the event you plan to power a small load with this device, the OUT1001 will either be sourcing or sinking current when in use.
	~~The OUT1001 may have an unpredictable output voltage for a very short time immediately after the device changes modes~~, ~~or is turned on. If this is a problem~~ in ~~your application and~~ you ~~have no way~~ to ~~ignore it via software~~, ~~we recommend using a [[Solid State Relay Primer\|solid state relay]] to switch~~ the ~~output on once it has stabilized~~.

	~~===Current Sourcing and Sinking===~~		The device will be a sourcing current when the device is connected to a circuit with a lower voltage potential than its voltage setting. In this situation, the current will be flowing out from the OUT1001 into the circuit.
	~~To ensure maximum voltage precision across~~ the device~~'s full range, the OUT1001 Phidget should be subjected~~ to a ~~minimal current draw, ideally less~~ than ~~5mA in ±10V mode~~. ~~5V mode should only~~ be ~~used to set a voltage in high-impedance applications~~.

	~~However, in the event you plan to power a small load with this~~ device~~, it~~ will ~~either~~ be ~~sourcing or~~ sinking current when ~~in use. When it's~~ connected to a circuit with a ~~lower~~ voltage potential than its ~~own~~ voltage setting, ~~current will be flowing out from the OUT1001 into the circuit, so it will be sourcing current. When it's connected to a circuit with a higher voltage potential than~~ the ~~voltage it's set to,~~ current will flow from the circuit into the OUT1001 ~~for a current sinking situation~~.		The device will be a sinking current when the device is connected to a circuit with a higher voltage potential than its voltage setting. In this situation, the current will flow from the circuit into the OUT1001.

	[[Image:sourcesink_diagram.jpg\|link=\|600px\|center]]		[[Image:sourcesink_diagram.jpg\|link=\|600px\|center]]

Line 52:		Line 71:
	[[Image:sourcesink1001_10v.jpg\|link=\|650px\|center]]		[[Image:sourcesink1001_10v.jpg\|link=\|650px\|center]]


			For example, if the connected circuit is pulling 13mA of current, the OUT1001 will only be able to provide a maximum of 4V (in 0-5V mode), even if you try to set it to a higher value.}}

	~~For example, if~~ the ~~connected circuit~~ is ~~pulling 13mA of current, the OUT1001 will only be able to provide~~ a ~~maximum of 4V (~~in ~~0-5V mode)~~, ~~even if~~ you ~~try~~ to ~~set~~ it to ~~a higher value~~.		{{UGC-Entry\|I’m seeing strange readings when I start my program or when switching voltage range\|
			\|
	{{~~UGnext\|~~}}		The OUT1001 may have an unpredictable output voltage for a very short time immediately after the device changes modes or is turned on. If this is a problem in your application, and you have no way to ignore it via software, we recommend using a [[Solid_State_Relay_Primer\|solid-state relay]] to switch the output on once it has stabilized.}}
			{{UGC-End}}

Jdecoux at 16:33, 17 October 2019

2019-10-17T16:33:00Z

← Older revision		Revision as of 16:33, 17 October 2019
Line 27:		Line 27:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\|~~This Phidget is compatible with the {{ExampleLink\|VoltageOutput}}.~~}}		{{ugUsingYourOwnProgram\|OUT1001}}

	==Technical Details==		==Technical Details==

Jdecoux: /* Using Your Own Program */

2018-08-28T17:01:39Z

Using Your Own Program

← Older revision		Revision as of 17:01, 28 August 2018
Line 27:		Line 27:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	~~===Using Your Own Program===~~		{{ugUsingYourOwnProgram\|This Phidget is compatible with the {{ExampleLink\|VoltageOutput}}.}}

	~~You are now ready to start writing your own code for the device. The best way to do that is to start from our examples:~~

	This Phidget is compatible with the {{ExampleLink\|VoltageOutput}}.

	Once you have your example, you will need to follow the instructions on the page for your programming language to get it running. To find these instructions, select your programming language from the [[Software_Overview#Language_Support\|Software Overview]] page.

	==Technical Details==		==Technical Details==

Jdecoux at 19:06, 27 August 2018

2018-08-27T19:06:51Z

@@ Line 24: / Line 24: @@
 {{ugVoltageOutput|OUT1001|, labelled ''Isolated 12-bit Voltage Output Phidget'', }}
 *Select the ''Voltage Output Range'' from the drop-down menu. You can choose between 0-5V output or ±10V output.
 ==Technical Details==