HIN1000 User Guide - Revision history

Mparadis at 21:14, 17 January 2022

2022-01-17T21:14:42Z

← Older revision		Revision as of 21:14, 17 January 2022
Line 38:		Line 38:
	{{UGC-Graphing}}		{{UGC-Graphing}}
	{{UGC-DataInterval}}		{{UGC-DataInterval}}
			{{UGC-Firmware}}
	{{UGC-Entry\|Recalibration\|\|		{{UGC-Entry\|Recalibration\|\|
	The capacitive touch sensors rely on checking capacitance against a threshold to detect when they are touched. As a result you need to keep a good baseline of the capacitance of the sensor's environment. The HIN1000 will recalibrate its baseline levels if it detects a constant touch for more than 60 seconds, in order to prevent getting stuck in a touched state. Similarly, it will recalibrate its baseline capacitance to adjust to falling capacitance (such as when it is moved away from a surface) in order to prevent getting stuck in a not-touched state. The latter adjustment happens soon after the baseline is detected to have fallen.		The capacitive touch sensors rely on checking capacitance against a threshold to detect when they are touched. As a result you need to keep a good baseline of the capacitance of the sensor's environment. The HIN1000 will recalibrate its baseline levels if it detects a constant touch for more than 60 seconds, in order to prevent getting stuck in a touched state. Similarly, it will recalibrate its baseline capacitance to adjust to falling capacitance (such as when it is moved away from a surface) in order to prevent getting stuck in a not-touched state. The latter adjustment happens soon after the baseline is detected to have fallen.

Mparadis at 20:33, 28 January 2021

2021-01-28T20:33:47Z

@@ Line 5: / Line 5: @@
 ==Part 1: Setup==
-{{UGIntro|HIN1000}}
+{{PT1 Deck Sequence}}
 == Part 2: Using Your Phidget ==

Mparadis: /* Part 4: Advanced Topics and Troubleshooting */

2021-01-06T21:19:45Z

Part 4: Advanced Topics and Troubleshooting

← Older revision		Revision as of 21:19, 6 January 2021
Line 49:		Line 49:
	{{UGC-Start}}		{{UGC-Start}}
	{{UGC-Addressing}}		{{UGC-Addressing}}
			{{UGC-Graphing}}
	{{UGC-DataInterval}}		{{UGC-DataInterval}}
	{{UGC-Entry\|Recalibration\|\|		{{UGC-Entry\|Recalibration\|\|

Mparadis at 19:46, 4 August 2020

2020-08-04T19:46:55Z

← Older revision		Revision as of 19:46, 4 August 2020
Line 1:		Line 1:
	__NOINDEX__		__NOINDEX__
			__NOTOC__
	<metadesc>The Touch Keypad Phidget has an array of capactive touch buttons as a unique way to control your Phidgets or provide user input to your program.</metadesc>		<metadesc>The Touch Keypad Phidget has an array of capactive touch buttons as a unique way to control your Phidgets or provide user input to your program.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]

	==~~Getting Started~~==		==Part 1: Setup==
	{{UGIntro\|HIN1000}}		{{UGIntro\|HIN1000}}
	* [{{SERVER}}/products.php?product_id=HIN1000 HIN1000 Touch Keypad Phidget]		* [{{SERVER}}/products.php?product_id=HIN1000 HIN1000 Touch Keypad Phidget]
Line 17:		Line 18:
	<br clear="all">		<br clear="all">

	~~==Using the~~ HIN1000==		{{UGcontrolpanel\|HIN1000}}

	~~{{UGcontrolpanel\|HIN1000}}~~		== Part 2: Using Your Phidget ==

			===About===
			The Touch Keypad Phidget provides seven capacitive touch regions with adjustable sensitivity.

			===Explore Your Phidget Channels Using The Control Panel===

			You can use your Control Panel to explore your Phidget's channels.

	~~{{ugCapacitiveTouch\|HIN1000}}~~		'''1.''' Open your Control Panel, and you will find the following channels:

	~~{{ugAddressingInformation}}~~		[[Image:HIN1000_Panel.jpg\|link=\|center]]

	~~{{ugUsingYourOwnProgram\|HIN1000}}~~		'''2.''' Double click on a channel to open an example program. Each channel belongs to the '''CapacitiveTouch''' channel class:

	~~==Technical Details==~~		{{UGC-Start}}

	~~===Re~~-~~Calibration===~~		{{UGC-Entry\|Capacitive Touch Sensor:\| Detects a touch or the close proximity of your hand or other conductive objects\|
			In your Control Panel, double click on "Capacitive Touch Sensor":

	~~Since capacitive touch sensors rely on checking capacitance against a threshold to detect when they are touched, they need to keep a good baseline of the capacitance of their environment. The~~ HIN1000 ~~will re~~-calibrate its baseline levels if it detects a constant touch for more than 60 seconds, in order to prevent getting stuck in a touched state. Similarly, it will re-calibrate its baseline capacitance to adjust to falling capacitance (such as when it is moved away from a surface) in order to prevent getting stuck in a not-touched state. The latter adjustment happens soon after the baseline is detected to have fallen.		[[Image:HIN1000-CapacitiveTouch.jpg\|center\|link=]]}}

	~~===Current Consumption===~~		{{UGC-End}}

	The current consumption of the HIN1000 varies depending on the data interval that you choose. When it is connected but not configured, it will draw a minimal current of around 50 µA. Once it has been configured, current consumption will increase as the interval between data events is shortened, as illustrated by this graph:		{{UG-Part3}}

	~~[[Image~~:HIN1000-~~current~~.~~jpg\|link=\|885px]]~~		== Part 4: Advanced Topics and Troubleshooting ==
			{{UGC-Start}}
			{{UGC-Addressing}}
			{{UGC-DataInterval}}
			{{UGC-Entry\|Recalibration\|\|
			The capacitive touch sensors rely on checking capacitance against a threshold to detect when they are touched. As a result you need to keep a good baseline of the capacitance of the sensor's environment. The HIN1000 will recalibrate its baseline levels if it detects a constant touch for more than 60 seconds, in order to prevent getting stuck in a touched state. Similarly, it will recalibrate its baseline capacitance to adjust to falling capacitance (such as when it is moved away from a surface) in order to prevent getting stuck in a not-touched state. The latter adjustment happens soon after the baseline is detected to have fallen.
			}}

	{{~~UGnext\|~~}}		{{UGC-End}}

Jdecoux at 16:30, 17 October 2019

2019-10-17T16:30:01Z

← Older revision		Revision as of 16:30, 17 October 2019
Line 25:		Line 25:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\|~~This Phidget is compatible with the {{ExampleLink\|CapacitiveTouch}}.~~}}		{{ugUsingYourOwnProgram\|HIN1000}}

	==Technical Details==		==Technical Details==

Jdecoux at 16:12, 28 August 2018

2018-08-28T16:12:55Z

← Older revision		Revision as of 16:12, 28 August 2018
Line 25:		Line 25:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	{{ugUsingYourOwnProgram\| {{ExampleLink\|CapacitiveTouch}}.}}		{{ugUsingYourOwnProgram\|This Phidget is compatible with the {{ExampleLink\|CapacitiveTouch}}.}}

	==Technical Details==		==Technical Details==

Jdecoux: /* Using Your Own Program */

2018-08-27T22:12:42Z

Using Your Own Program

← Older revision		Revision as of 22:12, 27 August 2018
Line 25:		Line 25:
	{{ugAddressingInformation}}		{{ugAddressingInformation}}

	~~===Using Your Own Program===~~		{{ugUsingYourOwnProgram\| {{ExampleLink\|CapacitiveTouch}}.}}

	~~You are now ready to start writing your own code for the device. The best way to do that is to start from our examples:~~

	~~This Phidget is compatible with the~~ {{ExampleLink\|CapacitiveTouch}}.

	Once you have your example, you will need to follow the instructions on the page for your programming language to get it running. To find these instructions, select your programming language from the [[Software_Overview#Language_Support\|Software Overview]] page.

	==Technical Details==		==Technical Details==

Jdecoux at 18:12, 27 August 2018

2018-08-27T18:12:50Z

← Older revision		Revision as of 18:12, 27 August 2018
Line 22:		Line 22:

	{{ugCapacitiveTouch\|HIN1000}}		{{ugCapacitiveTouch\|HIN1000}}

			{{ugAddressingInformation}}

			===Using Your Own Program===

			You are now ready to start writing your own code for the device. The best way to do that is to start from our examples:

			This Phidget is compatible with the {{ExampleLink\|CapacitiveTouch}}.

			Once you have your example, you will need to follow the instructions on the page for your programming language to get it running. To find these instructions, select your programming language from the [[Software_Overview#Language_Support\|Software Overview]] page.

	==Technical Details==		==Technical Details==

Mparadis at 15:59, 7 June 2018

2018-06-07T15:59:34Z

← Older revision		Revision as of 15:59, 7 June 2018
Line 8:		Line 8:
	* {{VINTHub}}		* {{VINTHub}}
	* USB cable and computer		* USB cable and computer
	* [{{~~SERVER~~}}~~/?view=comparetable&rel=Phidget%20Cables Phidget cable]~~		* {{CT\|PhidgetCable\|Phidget cable}}

	Next, you will need to connect the pieces:		Next, you will need to connect the pieces:

Mparadis at 20:26, 8 May 2018

2018-05-08T20:26:21Z

← Older revision		Revision as of 20:26, 8 May 2018
Line 1:		Line 1:
			__NOINDEX__
	<metadesc>The Touch Keypad Phidget has an array of capactive touch buttons as a unique way to control your Phidgets or provide user input to your program.</metadesc>		<metadesc>The Touch Keypad Phidget has an array of capactive touch buttons as a unique way to control your Phidgets or provide user input to your program.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]