ENC4110-4114 User Guide - Revision history

Mparadis at 19:26, 13 December 2018

2018-12-13T19:26:49Z

← Older revision		Revision as of 19:26, 13 December 2018
Line 1:		Line 1:
			[[Category:UserGuide]]
	== Mounting the Encoder to a Surface ==		== Mounting the Encoder to a Surface ==

Mparadis: /* Cable Mounts */

2018-08-03T19:00:43Z

Cable Mounts

← Older revision		Revision as of 19:00, 3 August 2018
Line 25:		Line 25:

	== Cable Mounts ==		== Cable Mounts ==

			If you need to secure any slack in the cable, you can use these plastic clips to mount the cable to a surface.

	[[Image:ENC4110_Cablemount.jpeg\|300px\|link=]]		[[Image:ENC4110_Cablemount.jpeg\|300px\|link=]]

Mparadis: /* Debris Shield */

2018-08-03T18:59:51Z

Debris Shield

← Older revision		Revision as of 18:59, 3 August 2018
Line 21:		Line 21:
	== Debris Shield ==		== Debris Shield ==
	[[Image:ENC4110_Debris.jpeg\|300px\|right\|link=]]		[[Image:ENC4110_Debris.jpeg\|300px\|right\|link=]]
	The debris shield protects the encoder from splashes of liquid or dust and debris that would interfere with the encoder if it falls into the track. The shield is not connected to the encoder, but it mounted separately by the screw holes along ~~the~~ length.		The debris shield protects the encoder from splashes of liquid or dust and debris that would interfere with the encoder if it falls into the track. The shield is not connected to the encoder, but it mounted separately by the screw holes along its length.
	<br clear="all">		<br clear="all">

Mparadis: /* Debris Shield */

2018-07-27T21:11:23Z

Debris Shield

← Older revision		Revision as of 21:11, 27 July 2018
Line 20:		Line 20:

	== Debris Shield ==		== Debris Shield ==
			[[Image:ENC4110_Debris.jpeg\|300px\|right\|link=]]
	[[Image:ENC4110_Debris.jpeg\|300px\|link=]]		The debris shield protects the encoder from splashes of liquid or dust and debris that would interfere with the encoder if it falls into the track. The shield is not connected to the encoder, but it mounted separately by the screw holes along the length.
			<br clear="all">

	== Cable Mounts ==		== Cable Mounts ==

	[[Image:ENC4110_Cablemount.jpeg\|300px\|link=]]		[[Image:ENC4110_Cablemount.jpeg\|300px\|link=]]

Mparadis: /* Carriage Mounting Plates */

2018-07-27T21:06:57Z

Carriage Mounting Plates

← Older revision		Revision as of 21:06, 27 July 2018
Line 11:		Line 11:
	== Carriage Mounting Plates ==		== Carriage Mounting Plates ==

	[[Image:ENC4110_Plate1.jpeg\|~~300px~~\|link=]] [[Image:ENC4110_Plate2.jpeg\|~~300px~~\|link=]] [[Image:ENC4110_Plate3.jpeg\|~~300px~~\|link=]] [[Image:ENC4110_Plate4.jpeg\|300px\|link=]]		The linear encoder comes with two different mounting plates for the carriage. You can use the bolts to attach them directly on top (you may need to use washers in order for the bolts to fit). The plate can then be attached to the moving part of your system, which should be self-supporting; don't put weight directly on the carriage. You can also connect them to one another using the bolts (nuts not included).

			[[Image:ENC4110_Plate1.jpeg\|280px\|link=]] [[Image:ENC4110_Plate2.jpeg\|280px\|link=]] [[Image:ENC4110_Plate3.jpeg\|280px\|link=]]

			You can also mount these plates on the side of the carriage using the bolts.

			[[Image:ENC4110_Plate4.jpeg\|300px\|link=]]

	== Debris Shield ==		== Debris Shield ==

Mparadis at 20:56, 27 July 2018

2018-07-27T20:56:25Z

← Older revision		Revision as of 20:56, 27 July 2018
Line 3:		Line 3:
	This linear encoder has mounting holes on either end that allow it to be mounted perpendicular or parallel to a surface.		This linear encoder has mounting holes on either end that allow it to be mounted perpendicular or parallel to a surface.

	[[Image:~~ENC4110_Plate1~~\|link=]] [[Image:~~ENC4110_Plate2~~\|link=]]		[[Image:ENC4110_Mount1.jpeg\|300px\|link=]] [[Image:ENC4110_Mount2.jpeg\|314px\|link=]]

	When mounting the encoder to a surface, you should take great care in making sure that it lies completely flat and parallel to the moving part it'll be measuring. Any small misalignment can cause inaccuracy in the measurement and strain on the mechanical parts.		When mounting the encoder to a surface, you should take great care in making sure that it lies completely flat and parallel to the moving part it'll be measuring. Any small misalignment can cause inaccuracy in the measurement and strain on the mechanical parts. Metal shims are included in case you need to raise one end slightly.

			[[Image:ENC4110_Shim1.jpeg\|300px\|link=]] [[Image:ENC4110_Shim2.jpeg\|300px\|link=]]

	== Carriage Mounting Plates ==		== Carriage Mounting Plates ==

			[[Image:ENC4110_Plate1.jpeg\|300px\|link=]] [[Image:ENC4110_Plate2.jpeg\|300px\|link=]] [[Image:ENC4110_Plate3.jpeg\|300px\|link=]] [[Image:ENC4110_Plate4.jpeg\|300px\|link=]]

	== Debris Shield ==		== Debris Shield ==

			[[Image:ENC4110_Debris.jpeg\|300px\|link=]]

	== Cable Mounts ==		== Cable Mounts ==

			[[Image:ENC4110_Cablemount.jpeg\|300px\|link=]]

Mparadis: Created page with "== Mounting the Encoder to a Surface == This linear encoder has mounting holes on either end that allow it to be mounted perpendicular or parallel to a surface. Image:ENC..."

2018-07-26T21:27:43Z

Created page with "== Mounting the Encoder to a Surface == This linear encoder has mounting holes on either end that allow it to be mounted perpendicular or parallel to a surface. Image:ENC..."

New page

== Mounting the Encoder to a Surface ==

This linear encoder has mounting holes on either end that allow it to be mounted perpendicular or parallel to a surface.

[[Image:ENC4110_Plate1|link=]] [[Image:ENC4110_Plate2|link=]]

When mounting the encoder to a surface, you should take great care in making sure that it lies completely flat and parallel to the moving part it'll be measuring. Any small misalignment can cause inaccuracy in the measurement and strain on the mechanical parts.

== Carriage Mounting Plates ==

== Debris Shield ==

== Cable Mounts ==