3052 User Guide - Revision history

Mparadis at 19:58, 1 June 2023

2023-06-01T19:58:08Z

← Older revision		Revision as of 19:58, 1 June 2023
Line 26:		Line 26:
	==Technical Details==		==Technical Details==
	===General===		===General===
	Solid State Relays, or SSRs, are devices designed to operate like standard relays but without mechanical motion. Built instead out of silicon transistors, SSRs allow currents and voltages to be switched by simple digital signals from a microprocessor or any other device that can supply the small amount of current needed to activate the SSR’s internal switching mechanism. For more information on solid state relays, refer to the [[Solid State Relay ~~Primer~~\|SSR ~~Primer~~]].		Solid State Relays, or SSRs, are devices designed to operate like standard relays but without mechanical motion. Built instead out of silicon transistors, SSRs allow currents and voltages to be switched by simple digital signals from a microprocessor or any other device that can supply the small amount of current needed to activate the SSR’s internal switching mechanism. For more information on solid state relays, refer to the [[Solid State Relay Guide\|SSR Guide]].

	===Protection Devices===		===Protection Devices===

Mparadis: /* Getting Started */

2019-12-09T21:50:57Z

Getting Started

← Older revision		Revision as of 21:50, 9 December 2019
Line 3:		Line 3:
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==Getting Started==		==Getting Started==
	{{~~UgSensorIntro\|~~3052\|SSR Relay Board 2.5A\|~~Digital Output port~~}}		Welcome to the 3052 user guide! In order to get started, make sure you have the following hardware on hand:
			*[{{SERVER}}/products.php?product_id=3052 3052 - SSR Relay Board 2.5A]
			* Either the [{{SERVER}}/products.php?product_id=1018 1018] or [{{SERVER}}/products.php?product_id=OUT1100 OUT1100]. We will be using the [{{SERVER}}/products.php?product_id=1018 1018] for this guide.
			* USB cable and computer
			* {{CT\|PhidgetCable\|Phidget cable}}
	*something to use with the 3052 (e.g. a series circuit)		*something to use with the 3052 (e.g. a series circuit)

Mparadis at 20:37, 8 May 2018

2018-05-08T20:37:56Z

← Older revision		Revision as of 20:37, 8 May 2018
Line 1:		Line 1:
			__NOINDEX__
	<metadesc>Rated for 28VAC/2.5amp or 40VDC/2.5amp switching, Phidgets' SSR Relay Board is controlled by a digital output.</metadesc>		<metadesc>Rated for 28VAC/2.5amp or 40VDC/2.5amp switching, Phidgets' SSR Relay Board is controlled by a digital output.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]

Mparadis at 16:34, 29 November 2017

2017-11-29T16:34:52Z

← Older revision		Revision as of 16:34, 29 November 2017
Line 1:		Line 1:
			<metadesc>Rated for 28VAC/2.5amp or 40VDC/2.5amp switching, Phidgets' SSR Relay Board is controlled by a digital output.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==Getting Started==		==Getting Started==

Lmpacent at 19:33, 21 June 2017

2017-06-21T19:33:56Z

← Older revision		Revision as of 19:33, 21 June 2017
Line 5:		Line 5:

	Next, you will need to connect the pieces:		Next, you will need to connect the pieces:
	[[Image:3052_1_Connecting_The_Hardware.jpg\|~~400px~~\|right\|link=]]		[[Image:3052_1_Connecting_The_Hardware.jpg\|500px\|right\|link=]]
	# Connect the circuit to the load terminals of the 3052.		# Connect the circuit to the load terminals of the 3052.
	# Connect the 3052 to the 1018 by connecting a wire from the terminal block marked with a '''+''' to a Digital Output and another wire from the terminal block marked with a '''-''' to any ground terminal on the 1018.		# Connect the 3052 to the 1018 by connecting a wire from the terminal block marked with a '''+''' to a Digital Output and another wire from the terminal block marked with a '''-''' to any ground terminal on the 1018.

Lmpacent at 17:36, 19 June 2017

2017-06-19T17:36:53Z

← Older revision		Revision as of 17:36, 19 June 2017
Line 26:		Line 26:

	===Using the SSR Board===		===Using the SSR Board===
	Using the SSR Relay Board in your application is typically done according to the diagram ~~on the right~~, though there are other implementations for it as well.		Using the SSR Relay Board in your application is typically done according to the diagram below, though there are other implementations for it as well.

	[[File:3052_0_Use_Diagram.jpg\|400px\|link=\|center]]		[[File:3052_0_Use_Diagram.jpg\|400px\|link=\|center]]

Lmpacent at 17:27, 19 June 2017

2017-06-19T17:27:15Z

← Older revision		Revision as of 17:27, 19 June 2017
Line 1:		Line 1:
	[[Category:UserGuide]]		[[Category:UserGuide]]
			==Getting Started==
			{{UgSensorIntro\|3052\|SSR Relay Board 2.5A\|Digital Output port}}
			*something to use with the 3052 (e.g. a series circuit)

	~~===Required Hardware===~~		Next, you will need to connect the pieces:

	* A [{{SERVER}}/products.php?product_id=3052 3052 Solid State Relay Phidget]
	* An InterfaceKit or device with a digital output
	* A series electric circuit to ~~test~~ the ~~relay~~
	* Pieces of hook-up wire
	* A USB Cable
	* A computer

	~~===Connecting the Pieces===~~
	[[Image:3052_1_Connecting_The_Hardware.jpg\|400px\|right\|link=]]		[[Image:3052_1_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the circuit to the load terminals of the ~~relay board~~.		# Connect the circuit to the load terminals of the 3052.
	# Connect the ~~SSR Relay Phidget~~ to the ~~InterfaceKit~~ by connecting a wire from the terminal block marked with a + to a ~~digital output~~ and another wire from the terminal block marked with a - to any ground terminal on the ~~InterfaceKit~~.		# Connect the 3052 to the 1018 by connecting a wire from the terminal block marked with a '''+''' to a Digital Output and another wire from the terminal block marked with a '''-''' to any ground terminal on the 1018.
	# Connect the ~~InterfaceKit~~ to the computer using the USB cable.		# Connect the 1018 to the computer using the USB cable.

	<br clear="all">		<br clear="all">
			{{UGIntroDone\|3052}}

	==~~Testing~~ Using ~~Windows~~==		==Using the 3052==
			{{UGcontrolpanelSensor\|3052\|1018}}
	{{~~UGcontrolpanel~~\|1018}}

	{{~~ugDigitalOutput}}~~		{{UGSensorDigitalOutput\|This will change the relay state.}}

	~~{{UGotheros~~}}

	==Technical Details==		==Technical Details==
	===~~Solid State Relays~~===		===General===
	Solid State Relays, or SSRs, are devices designed to operate like standard relays but without mechanical motion. Built instead out of silicon transistors, SSRs allow currents and voltages to be switched by simple digital signals from a microprocessor or any other device that can supply the small amount of current needed to activate the SSR’s internal switching mechanism. For more information on solid state relays, refer to the [[Solid State Relay Primer\|SSR Primer]].		Solid State Relays, or SSRs, are devices designed to operate like standard relays but without mechanical motion. Built instead out of silicon transistors, SSRs allow currents and voltages to be switched by simple digital signals from a microprocessor or any other device that can supply the small amount of current needed to activate the SSR’s internal switching mechanism. For more information on solid state relays, refer to the [[Solid State Relay Primer\|SSR Primer]].

	===Protection Devices===		===Protection Devices===
	The ~~SSR Board~~ is safe to use with sensitive control devices like microprocessors, and will not damage a Phidget ~~device~~ or your PC. Optoisolation between the control inputs and outputs of the SSR in the form of a GaAs LED paired with a set of optically-controlled MOSFETs provides protection from output to input. An on-board 47V bidirectional transorb across the relay output protects the board from static electricity and surges from inductive loads.		The 3052 is safe to use with sensitive control devices like microprocessors, and will not damage a Phidget or your PC. Optoisolation between the control inputs and outputs of the SSR in the form of a GaAs LED paired with a set of optically-controlled MOSFETs provides protection from output to input. An on-board 47V bidirectional transorb across the relay output protects the board from static electricity and surges from inductive loads.

	===Using the SSR Board===		===Using the SSR Board===
	~~{{UGbox\|~~
	Using the SSR Relay Board in your application is typically done according to the diagram on the right, though there are other implementations for it as well.		Using the SSR Relay Board in your application is typically done according to the diagram on the right, though there are other implementations for it as well.
	\|
	[[File:3052_0_Use_Diagram.jpg\|400px\|link=]]		[[File:3052_0_Use_Diagram.jpg\|400px\|link=\|center]]
	~~\|\|}}~~

	{{UGnext\|}}		{{UGnext\|}}

Mparadis at 16:31, 6 June 2017

2017-06-06T16:31:41Z

← Older revision		Revision as of 16:31, 6 June 2017
Line 3:		Line 3:
	===Required Hardware===		===Required Hardware===

	* A 3052 ~~SSR~~ Relay Phidget		* A [{{SERVER}}/products.php?product_id=3052 3052 Solid State Relay Phidget]
	* An InterfaceKit or device with a digital output		* An InterfaceKit or device with a digital output
	* A series electric circuit to test the relay		* A series electric circuit to test the relay

Mparadis at 08:10, 28 October 2016

2016-10-28T08:10:06Z

← Older revision		Revision as of 08:10, 28 October 2016
Line 11:		Line 11:

	===Connecting the Pieces===		===Connecting the Pieces===
	[[Image:~~3052_0_Connecting_The_Hardware~~.jpg\|400px\|right\|link=]]		[[Image:3052_1_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the circuit to the load terminals of the relay board.		# Connect the circuit to the load terminals of the relay board.
	# Connect the SSR Relay Phidget to the InterfaceKit by connecting a wire from the terminal block marked with a + to a digital output and another wire from the terminal block marked with a - to any ground terminal on the InterfaceKit.		# Connect the SSR Relay Phidget to the InterfaceKit by connecting a wire from the terminal block marked with a + to a digital output and another wire from the terminal block marked with a - to any ground terminal on the InterfaceKit.

Mparadis: /* Product History */

2016-09-16T15:57:25Z

Product History

← Older revision		Revision as of 15:57, 16 September 2016
Line 40:		Line 40:

	{{UGnext\|}}		{{UGnext\|}}

	~~==Product History==~~
	~~{{UGhist}}~~
	~~{{UGrow2\|3052_0\|October 2007 \|0 \|N/A \|Product Release }}~~
	~~{{UGrow2\|3052_1\|October 2007 \|1 \|N/A \|Replaced connector w/ terminal blocks }}~~