1124 User Guide - Revision history

Mparadis: /* Technical Details */

2021-08-04T15:46:15Z

Technical Details

← Older revision		Revision as of 15:46, 4 August 2021
Line 20:		Line 20:

	==Technical Details==		==Technical Details==

			===Higher Range Measurements===

			If you don't use setSensorType() and simply convert from voltage to degrees using the formula below, you can measure temperatures up to 150°C. However, the components on the 1124 are rated for a maximum of 80°C, so this should only be done for short periods for testing purposes.

	===Formulas===		===Formulas===

Mparadis: /* Technical Details */

2021-08-04T15:41:23Z

Technical Details

← Older revision		Revision as of 15:41, 4 August 2021
Line 20:		Line 20:

	==Technical Details==		==Technical Details==
	~~===General===~~
	The temperature sensor component is rated at -50°C to +150°C, but the other components on the board, the connector and the cable are rated at -30°C to +80°C. In a fast prototyping environment the temperature sensor
	~~board can be pushed to the ratings of the sensor component, but you should use the lower temperature ratings if you plan to use the 1124 in a commercial application.~~

	===Formulas===		===Formulas===

Mparadis: /* Formulas */

2018-05-10T17:46:27Z

Formulas

← Older revision		Revision as of 17:46, 10 May 2018
Line 25:		Line 25:

	===Formulas===		===Formulas===
	{{UGSensorFormula\|temperature (°C)}} The Formula to translate voltage from the sensor into temperature is:		{{UGSensorFormula\|temperature (°C)}} The Formula to translate voltage ratio from the sensor into temperature is:


	::<math>		::<math>
	\text{Temperature (}^\circ \text{C)} = \text{(~~Voltage~~} \times \text{44.~~444~~) - 61.111}		\text{Temperature (}^\circ \text{C)} = \text{(VoltageRatio} \times \text{222.2) - 61.111}
	</math>		</math>
	<br clear="all">		<br clear="all">

Mparadis at 20:56, 8 May 2018

2018-05-08T20:56:35Z

← Older revision		Revision as of 20:56, 8 May 2018
Line 1:		Line 1:
			__NOINDEX__
	<metadesc>The Phidgets Temperature Sensor measures the ambient air temperature surrounding the board. Connects to an Analog Input or VINT Hub port.</metadesc>		<metadesc>The Phidgets Temperature Sensor measures the ambient air temperature surrounding the board. Connects to an Analog Input or VINT Hub port.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]

Jdecoux at 17:25, 11 April 2018

2018-04-11T17:25:58Z

← Older revision		Revision as of 17:25, 11 April 2018
Line 7:		Line 7:
	Next, you will need to connect the pieces:		Next, you will need to connect the pieces:
	[[Image:1124_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]		[[Image:1124_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the 1124 to the ~~1018~~ with the Phidget cable.		# Connect the 1124 to the HUB0000 with the Phidget cable.
	# Connect the ~~1018~~ to your computer with the USB cable.		# Connect the HUB0000 to your computer with the USB cable.

	<br clear="all">		<br clear="all">
Line 14:		Line 14:

	==Using the 1124==		==Using the 1124==
	{{UGcontrolpanelSensor\|1124\|~~1018~~}}		{{UGcontrolpanelSensor\|1124\|HUB0000}}

	{{UGSensorVoltageRatioInput\|1124\|temperature (°C)}}		{{UGSensorVoltageRatioInput\|1124\|temperature (°C)}}

Mparadis at 16:15, 29 November 2017

2017-11-29T16:15:44Z

← Older revision		Revision as of 16:15, 29 November 2017
Line 1:		Line 1:
			<metadesc>The Phidgets Temperature Sensor measures the ambient air temperature surrounding the board. Connects to an Analog Input or VINT Hub port.</metadesc>
	[[Category:UserGuide]]		[[Category:UserGuide]]
	==Getting Started==		==Getting Started==

Lmpacent at 16:33, 19 June 2017

2017-06-19T16:33:19Z

← Older revision		Revision as of 16:33, 19 June 2017
Line 18:		Line 18:

	==Technical Details==		==Technical Details==
	===~~Temperature Range~~===		===General===
	The temperature sensor component is rated at -50°C to +150°C, but the other components on the board, the connector and the cable are rated at -30°C to +80°C. In a fast prototyping environment the temperature sensor		The temperature sensor component is rated at -50°C to +150°C, but the other components on the board, the connector and the cable are rated at -30°C to +80°C. In a fast prototyping environment the temperature sensor
	board can be pushed to the ratings of the sensor component, but you should use the lower temperature ratings if you plan to use the 1124 in a commercial application.		board can be pushed to the ratings of the sensor component, but you should use the lower temperature ratings if you plan to use the 1124 in a commercial application.

Lmpacent at 21:24, 16 June 2017

2017-06-16T21:24:10Z

← Older revision		Revision as of 21:24, 16 June 2017
Line 15:		Line 15:
	{{UGcontrolpanelSensor\|1124\|1018}}		{{UGcontrolpanelSensor\|1124\|1018}}

	{{UGSensorVoltageRatioInput\|1124\|temperature}}		{{UGSensorVoltageRatioInput\|1124\|temperature (°C)}}

	==Technical Details==		==Technical Details==
Line 23:		Line 23:

	===Formulas===		===Formulas===
	{{UGSensorFormula\|temperature}} The Formula to translate voltage from the sensor into temperature is:		{{UGSensorFormula\|temperature (°C)}} The Formula to translate voltage from the sensor into temperature is:

Lmpacent at 18:19, 16 June 2017

2017-06-16T18:19:19Z

← Older revision		Revision as of 18:19, 16 June 2017
Line 1:		Line 1:
	[[Category:UserGuide]]		[[Category:UserGuide]]
			==Getting Started==
			{{UgSensorIntro\|1124\|Precision Temperature Sensor\|Voltage Ratio Input port}}

	~~===Required Hardware===~~

	* A [{{SERVER}}/products.php?product_id=1124 1124 Temperature Sensor]		Next, you will need to connect the pieces:
	* An InterfaceKit or Hub to ~~read~~ the ~~sensor~~
	* A Phidget cable
	* A USB cable
	* A computer

	~~===Connecting the Pieces===~~
	[[Image:1124_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]		[[Image:1124_0_Connecting_The_Hardware.jpg\|400px\|right\|link=]]
	# Connect the ~~temperature sensor~~ to the ~~InterfaceKit or Hub~~ with the Phidget cable.		# Connect the 1124 to the 1018 with the Phidget cable.
	# Connect the ~~InterfaceKit or Hub~~ to your computer with the USB cable.		# Connect the 1018 to your computer with the USB cable.

	<br clear="all">		<br clear="all">
	~~==Testing Using Windows==~~		{{UGIntroDone\|1124}}

	{{~~UgSensor~~}}		==Using the 1124==
			{{UGcontrolpanelSensor\|1124\|1018}}

			{{UGSensorVoltageRatioInput\|1124\|temperature}}

	==Technical Details==		==Technical Details==
Line 25:		Line 23:

	===Formulas===		===Formulas===
	The Formula to translate voltage from the sensor into ~~Temperature~~ is:		{{UGSensorFormula\|temperature}} The Formula to translate voltage from the sensor into temperature is:


Line 31:		Line 29:
	\text{Temperature (}^\circ \text{C)} = \text{(Voltage} \times \text{44.444) - 61.111}		\text{Temperature (}^\circ \text{C)} = \text{(Voltage} \times \text{44.444) - 61.111}
	</math>		</math>
			<br clear="all">

	{{UGasens}}		{{UGasens}}

	{{UGnext\|}}		{{UGnext\|}}

Mparadis at 16:17, 6 June 2017

2017-06-06T16:17:32Z

← Older revision		Revision as of 16:17, 6 June 2017
Line 3:		Line 3:
	===Required Hardware===		===Required Hardware===

	* A 1124 Temperature Sensor		* A [{{SERVER}}/products.php?product_id=1124 1124 Temperature Sensor]
	* An InterfaceKit or Hub to read the sensor		* An InterfaceKit or Hub to read the sensor
	* A Phidget cable		* A Phidget cable