Replaced by the 3532_1 - Hollow Shaft Optical Encoder, the same encoder but with a Phidget encoder cable connector.
This sturdy optical quadrature encoder can be attached to the 8mm rear shaft of a motor without need for a shaft coupler. It has 360 counts (full quadrature cycles) per rotation and can be installed easily by fitting it over the shaft and tightening the set-screw. This encoder makes use of the index channel, sending one pulse for every full rotation.
This quadrature encoder can be read by an encoder interface by fitting the end of the cable with the appropriate connector. See the Connection & Compatibility tab for details.
This quadrature encoder must be read by an encoder interface. These interfaces will interpret the two quadrature signals in order to determine the continuous position of the rotating part. The following interfaces are compatible with this encoder:
Product | Encoder Interface | ||
---|---|---|---|
Part Number | Price | Number of Encoder Inputs | Count Rate Max |
PhidgetEncoder HighSpeed 4-Input
|
$80.00 | 4 | 1E+06 pulses/s |
PhidgetEncoder HighSpeed 4-Input
|
$75.00 | 4 | 1E+06 pulses/s |
PhidgetEncoder HighSpeed
|
$55.00 | 1 | 2E+06 pulses/s |
PhidgetEncoder HighSpeed
|
$50.00 | 1 | 1E+06 pulses/s |
PhidgetMotorControl 1-Motor
|
$75.00 | 1 | 500000 cycles/s |
DC Motor Phidget
|
$75.00 | 1 | 400000 pulses/s |
4A DC Motor Phidget
|
$40.00 | 1 | 400000 pulses/s |
Quadrature Encoder Phidget
|
$15.00 | 1 | 1E+06 pulses/s |
You can easily connect this encoder to a Phidgets encoder interface by cutting the end off of a Phidget encoder cable and soldering the wires to the encoder as described in this table. Below you'll find a list of available encoder cables:
|
Alternatively, you could buy the male connector (Molex part 50-57-9405), and crimp it onto the end of the cable, if you have the appropriate tools.
Product | Physical Properties | ||
---|---|---|---|
Part Number | Price | Cable Length | Cable Gauge |
HighSpeed Encoder Cable 50cm
|
$5.00 | 500 mm | 26 AWG |
Encoder Properties | |
---|---|
Output Circuit Type | Push-Pull |
Controlled By | Encoder Interface |
Encoder Resolution | 360 CPR |
Encoder Speed Max | 4500 RPM |
Electrical Properties | |
Supply Voltage Min | 5 V DC |
Supply Voltage Max | 5 V DC |
Output Frequency Max | 100 kHz |
Physical Properties | |
Shaft Diameter | (Inner) 8 mm |
Shaft Maximum Axial Load | 10 N |
Shaft Maximum Radial Load | 20 N |
Operating Humidity Min | 30 %RH |
Operating Humidity Max | (Non-condensing) 85 %RH |
Operating Temperature Min | -10 °C |
Operating Temperature Max | 70 °C |
IP Rating | IP54 |
Weight | 121 g |
Customs Information | |
Canadian HS Export Code | 9029.10.00 |
American HTS Import Code | 9029.10.80.00 |
Country of Origin | CN (China) |
Product | Encoder Properties | |||
---|---|---|---|---|
Part Number | Price | Output Circuit Type | Encoder Resolution | Encoder Speed Max |
Rotary Encoder with 4mm Shaft (360 CPR)
|
$50.00 | Push-Pull | 360 CPR | 3000 RPM |
Rotary Encoder - For 4mm Motor Shaft 300 CPR
|
$25.00 | Push-Pull | 300 CPR | 6000 RPM |
Rotary Encoder with 8mm Bore (500 CPR)
|
$50.00 | Push-Pull | 500 CPR | 4500 RPM |
Rotary Encoder - For 4mm Motor Shaft 40 CPR
|
$10.00 | Push-Pull | 40 CPR | 6000 RPM |
Rotary Encoder - 6mm Solid Shaft 600CPR
|
$25.00 | Push-Pull | 600 CPR | 6000 RPM |
Rotary Encoder - 6mm Solid Shaft 1000CPR with Index
|
$40.00 | Push-Pull | 1000 CPR | 6000 RPM |
Rotary Encoder - 8mm Solid Shaft 1000CPR with Index
|
$45.00 | Push-Pull | 1000 CPR | 6000 RPM |
Rotary Encoder - 12mm Solid Shaft 1000CPR with Index
|
$60.00 | Push-Pull | 1000 CPR | 2000 RPM |
Rotary Encoder - 12mm Hollow Shaft 1000CPR with Index
|
$50.00 | Push-Pull | 1000 CPR | 6000 RPM |
Rotary Encoder - For 5mm Motor Shaft 1000CPR
|
$30.00 | Push-Pull | 1000 CPR | 5000 RPM |